View AZ10LVEL16VST_1215043.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ARIZONA MICROTEK, INC.
AZ10LVEL16VS AZ100LVEL16VS
ECL/PECL Differential Receiver with Variable Output Swing FEATURES
* * * * * * 250ps Propagation Delay High Bandwidth Output Transitions Operating Range of 3.0V to 5.5V Internal Input Pulldown Resistors Functionally Equivalent to ON Semiconductor MC10EL16, MC100EL16 & MC100LVEL16 Variable Output Swing PACKAGE
SOIC 8 SOIC 8 TSSOP 8 TSSOP 8
1
PACKAGE AVAILABILITY PART NUMBER
AZ10LVEL16VSD AZ100LVEL16VSD AZ10LVEL16VST AZ100LVEL16VST
MARKING
AZM10 LV16VS AZM100 LV16VS AZT L16VS AZH L16VS
NOTES
1,2 1,2 1,2 1,2
DESCRIPTION
2
Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts) Tape & Reel. Date code format: "Y" or "YY" for year followed by "WW" for week on underside of part.
The AZ10/100LVEL16VS is a differential receiver with variable output swing. The LVEL16VS has functionality and output transition times similar to the EL16, with an input that controls the amplitude of the Q/Q outputs. The operational range of the LVEL16VS control input, VCTRL, is from VBB (full swing) to VCC (min. swing). Maximum swing is achieved by leaving the VCTRL pin open or by tying it to the negative supply (VEE). Simple control of the output swing can be obtained by a variable resistor between the VBB and VCC pins, with the wiper driving VCTRL. Typical application circuits and results are described in this Data Sheet. The LVEL16VS provides a VBB output for single-ended use or a DC bias reference for AC coupling to the device. For single-ended input applications, the VBB reference should be connected to one side of the D/D differential input pair. The input signal is then fed to the other D/D input. The VBB pin can support 1.5mA sink/source current. When used, the VBB pin should be bypassed to ground via a 0.01F capacitor. Under open input conditions internal input clamps will force the Q output LOW. NOTE: Specifications in the ECL/PECL tables are valid when thermal equilibrium is established. PIN DESCRIPTION PIN D, D VCTRL Q, Q VBB VCC VEE FUNCTION Data Inputs Output Swing Control Data Outputs Reference Voltage Output Positive Supply Negative Supply
VCTRL 1 8 VCC
D
2
7
Q
D
3
6
Q
VBB
4
5
VEE
LOGIC DIAGRAM AND PINOUT ASSIGNMENT 1630 S. STAPLEY DR., SUITE 127 * MESA, ARIZONA 85204 * USA * (480) 962-5881 * FAX (480) 890-2541 www.azmicrotek.com
AZ10LVEL16VS AZ100LVEL16VS
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Symbol VCC VI VEE VI IOUT TA TSTG Characteristic PECL Power Supply (VEE = 0V) PECL Input Voltage (VEE = 0V) ECL Power Supply (VCC = 0V) ECL Input Voltage (VCC = 0V) Output Current --- Continuous --- Surge Operating Temperature Range Storage Temperature Range Rating 0 to +8.0 0 to +6.0 -8.0 to 0 -6.0 to 0 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc Vdc Vdc mA C C
10K ECL DC Characteristics (VEE = -3.0V to -5.5V, VCC = GND)
Symbol VOH VOL VOL VIH VIL VBB IIH Characteristic
2
IIL IEE 1. 2.
Output HIGH Voltage Output LOW Voltage2 -1950 -1650 -1950 -1630 -1950 VCTRL = VBB1 Output LOW Voltage2 -1220 -1030 -1200 -1020 -1190 VCTRL = VCC Input HIGH Voltage -1230 -890 -1170 -840 -1130 Input LOW Voltage -1950 -1500 -1950 -1480 -1950 Reference Voltage -1450 -1300 -1400 -1270 -1370 Input HIGH Current 150 150 D, D VCTRL 40 40 Input LOW Current -150 -150 -150 D, D VCTRL 0.5 0.5 0.5 Power Supply Current 18 25 18 25 If VCTRL is Open Circuit, use the VOH (Max & Min) and VOL (VCTRL = VBB : Max only) limits. Each output is terminated through a 50 resistor to VCC - 2V.
Min -1080
-40C Typ
Max -890
Min -1020
0C Typ
Max -840
Min -980
25C Typ
Max -810 -1630
Min -910 -1950 -1190 -1060 -1950 -1330
85C Typ
Max -720 -1595 -1000 -720 -1445 -1190 150 40
Unit mV mV mV mV mV mV A A
-1150
-1020 -810 -1480 -1250 150 40
-150 0.5 18 25 21 26
mA
10K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)
Symbol VOH VOL VOL VIH VIL VBB IIH Characteristic
1,3
IIL IEE 1. 2. 3.
Output HIGH Voltage Output LOW Voltage1,3 1350 1650 1350 1670 1350 VCTRL = VBB2 1,3 Output LOW Voltage 2080 2270 2100 2280 2110 VCTRL = VCC Input HIGH Voltage1 2070 2410 2130 2460 2170 Input LOW Voltage1 1350 1800 1350 1820 1350 Reference Voltage1 1850 2000 1900 2030 1930 Input HIGH Current 150 150 D, D VCTRL 40 40 Input LOW Current D, D -150 -150 -150 VCTRL 0.5 0.5 0.5 Power Supply Current 18 25 18 25 For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value. If VCTRL is Open Circuit, use the VOH (Max & Min) and VOL (VCTRL = VBB : Max only) limits. Each output is terminated through a 50 resistor to VCC - 2V.
Min 2220
-40C Typ
Max 2410
Min 2280
0C Typ
Max 2460
Min 2320
25C Typ
Max 2490 1670
Min 2390 1350 2110 2240 1350 1970
85C Typ
Max 2580 1705 2300 2580 1855 2110 150 40
Unit mV mV mV mV mV mV A A
2150
2280 2490 1820 2050 150 40
-150 0.5 18 25 21 26
mA
November 2006 * REV - 2
www.azmicrotek.com 2
AZ10LVEL16VS AZ100LVEL16VS
10K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol VOH VOL VOL VIH VIL VBB IIH Characteristic
1,3
IIL IEE 1. 2. 3.
Output HIGH Voltage Output LOW Voltage1,3 3050 3350 3050 3350 3050 VCTRL = VBB2 1,3 Output LOW Voltage 3780 3970 3800 3980 3810 VCTRL = VCC 1 Input HIGH Voltage 3770 4110 3830 4160 3870 Input LOW Voltage1 3050 3500 3050 3520 3050 Reference Voltage1 3550 3700 3600 3730 3630 Input HIGH Current 150 150 D, D VCTRL 40 40 Input LOW Current -150 -150 -150 D, D VCTRL 0.5 0.5 0.5 Power Supply Current 18 25 18 25 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. If VCTRL is Open Circuit, use the VOH (Max & Min) and VOL (VCTRL = VBB : Max only) limits. Each output is terminated through a 50 resistor to VCC - 2V.
Min 3920
-40C Typ
Max 4110
Min 3980
0C Typ
Max 4160
Min 4020
25C Typ
Max 4190 3350
Min 4090 3050 3810 3940 3050 3670
85C Typ
Max 4280 3405 4000 4280 3555 3810 150 40
Unit mV mV mV mV mV V A A
3850
3980 4190 3520 3750 150 40
-150 0.5 18 25 21 26
mA
100K ECL DC Characteristics (VEE = -3.0V to -5.5V, VCC = GND)
Symbol VOH VOL VOL VIH VIL VBB IIH Characteristic
2
IIL IEE 1. 2.
Output HIGH Voltage Output LOW Voltage2 -1890 -1620 -1870 -1680 -1870 VCTRL = VBB1 2 Output LOW Voltage -1180 -975 -1135 -990 -1135 VCTRL = VCC Input HIGH Voltage -1165 -880 -1165 -880 -1165 Input LOW Voltage -1810 -1475 -1810 -1475 -1810 Reference Voltage -1420 -1260 -1420 -1260 -1420 Input HIGH Current 150 150 D, D VCTRL 40 40 Input LOW Current -150 -150 -150 D, D VCTRL 0.5 0.5 0.5 Power Supply Current 18 25 18 25 If VCTRL is Open Circuit, use the VOH (Max & Min) and VOL (VCTRL = VBB : Max only) limits. Each output is terminated through a 50 resistor to VCC - 2V.
Min -1085
-40C Typ -1005
Max -880
Min -1025
0C Typ -955
Max -880
Min -1025
25C Typ -955 -1775 -1065
Max -880 -1680 -990 -880 -1475 -1260 150 40
Min -1025 -1870 -1135 -1165 -1810 -1420
85C Typ -955
Max -880 -1680 -990 -880 -1475 -1260 150 40
Unit mV mV mV mV mV mV A A
-150 0.5 18 25 21 26
mA
100K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)
Symbol VOH VOL VOL VIH VIL VBB IIH Characteristic
1,3
IIL IEE 1. 2. 3.
Output HIGH Voltage Output LOW Voltage1,3 1410 1680 1430 1620 1430 VCTRL = VBB2 1,3 Output LOW Voltage 2120 2325 2165 2310 2165 VCTRL = VCC 1 Input HIGH Voltage 2135 2420 2135 2420 2135 Input LOW Voltage1 1490 1825 1490 1825 1490 Reference Voltage1 1880 2040 1880 2040 1880 Input HIGH Current 150 150 D, D VCTRL 40 40 Input LOW Current -150 -150 -150 D, D VCTRL 0.5 0.5 0.5 Power Supply Current 18 25 18 25 For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value. If VCTRL is Open Circuit, use the VOH (Max & Min) and VOL (VCTRL = VBB : Max only) limits. Each output is terminated through a 50 resistor to VCC - 2V.
Min 2215
-40C Typ 2295
Max 2420
Min 2275
0C Typ 2345
Max 2420
Min 2275
25C Typ 2345 1525 2235
Max 2420 1620 2310 2420 1825 2040 150 40
Min 2275 1430 2165 2135 1490 1880
85C Typ 2345
Max 2420 1620 2310 2420 1825 2040 150 40
Unit mV mV mV mV mV mV A A
-150 0.5 18 25 21 26
mA
November 2006 * REV - 2
www.azmicrotek.com 3
AZ10LVEL16VS AZ100LVEL16VS
100K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol VOH VOL VOL VIH VIL VBB IIH Characteristic
1,3
IIL IEE 1. 2. 3.
Output HIGH Voltage Output LOW Voltage1,3 3110 3380 3130 3320 3130 VCTRL = VBB2 1,3 Output LOW Voltage 3820 4025 3865 4010 3865 VCTRL = VCC 1 Input HIGH Voltage 3820 4025 3865 4010 3865 Input LOW Voltage1 3835 4120 3835 4120 3835 Reference Voltage1 3580 3740 3580 3740 3580 Input HIGH Current 150 150 D, D VCTRL 40 40 Input LOW Current -150 -150 -150 D, D VCTRL 0.5 0.5 0.5 Power Supply Current 18 25 18 25 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. If VCTRL is Open Circuit, use the VOH (Max & Min) and VOL (VCTRL = VBB : Max only) limits. Each output is terminated through a 50 resistor to VCC - 2V.
Min 3915
-40C Typ 3995
Max 4120
Min 3975
0C Typ 4045
Max 4120
Min 3975
25C Typ 4045 3225 3935 3935
Max 4120 3320 4010 4010 4120 3740 150 40
Min 3975 3130 3865 3865 3835 3580
85C Typ 4045
Max 4120 3320 4010 4010 4120 3740 150 40
Unit mV mV mV mV mV V A A
-150 0.5 18 25 21 26
mA
AC Characteristics (VEE = -3.0V to -5.5V; VCC = GND; VCTRL=VBB or VEE =GND; VCC = +3.0V to +5.5V; VCTRL=VBB)
Symbol tPLH / tPHL Characteristic Min Input to (DIFF) Output Delay (SE) tSKEW Duty Cycle Skew1 (Diff) VPP (AC) Minimum Input Swing2 150 150 150 150 Common Mode Range3 VEE + VCC - VEE + VCC - VEE + VCC - VEE + VCC VPP < 500mV 1.2 0.4 1.1 0.4 1.1 0.4 1.1 0.4 VCMR 1.5 0.4 1.4 0.4 1.4 0.4 1.4 0.4 VPP 500mV Output Rise/Fall Times Q tr / t f 100 260 100 260 100 260 100 260 (20% - 80%) 1. Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device. 2. VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed. 3. The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP(min) and 1V. -40C Typ 250 250 5 Max Min 175 125 0C Typ 250 250 5 Max 325 375 20 Min 175 125 25C Typ 250 250 5 Max 325 375 20 Min 205 155 85C Typ 280 280 5 Max 355 405 20 Unit ps ps ps mV V ps
November 2006 * REV - 2
www.azmicrotek.com 4
AZ10LVEL16VS AZ100LVEL16VS
Typical Voltage Output Swing at +25C, VCC Nom (see Figure 1 and Figure 2)
100
VSWING (% pk-pk differential)
1.500 V (100K ECL) 75 %OUT Vbb 100K ECL 50
25
0 0.0 0.4 0.8 1.2
VCTRL (V)
Vbb 1.320
1.6
Figure 1: Voltage Source Implementation VCTRL VCTRL
D 1 8 V CC
2
7
Q
V SWING
(pk-pk)
D
3
6
Q
50
V BB 4 5 VEE
50
-2V
Figure 2: Alternative Implementation 10k
VCTRL 1 8 V CC
D
2
7
Q
VSWING
(pk-pk)
D
3
6
Q
VBB
4
5
RL
VEE
RL
RL = 180@3.3V Supply; RL = 330@5.0V Supply
November 2006 * REV - 2
www.azmicrotek.com 5
AZ10LVEL16VS AZ100LVEL16VS PACKAGE DIAGRAM SOIC 8
NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm.
DIM A A1 A2 A3 bp c D E e HE L Lp Q v w y Z
MILLIMETERS MIN MAX 1.75 0.10 0.25 1.25 1.45 0.25 0.36 0.49 0.19 0.25 4.8 5.0 3.8 4.0 1.27 5.80 6.20 1.05 0.40 1.00 0.60 0.70 0.25 0.25 0.10 0.30 0.70 8O 0O
INCHES MIN MAX 0.069 0.004 0.010 0.049 0.057 0.01 0.014 0.019 0.0075 0.0100 0.19 0.20 0.15 0.16 0.050 0.228 0.244 0.041 0.016 0.039 0.024 0.028 0.01 0.01 0.004 0.012 0.028 0O 8O
November 2006 * REV - 2
www.azmicrotek.com 6
AZ10LVEL16VS AZ100LVEL16VS PACKAGE DIAGRAM TSSOP 8
NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm.
DIM A A1 A2 A3 bp c D E e HE L Lp v w y Z
MILLIMETERS MIN MAX 1.10 0.05 0.15 0.80 0.95 0.25 0.25 0.45 0.15 0.28 2.90 3.10 2.90 3.10 0.65 4.70 5.10 0.94 0.40 0.70 0.10 0.10 0.10 0.35 0.70 6O 0O
November 2006 * REV - 2
www.azmicrotek.com 7
AZ10LVEL16VS AZ100LVEL16VS
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
November 2006 * REV - 2
www.azmicrotek.com 8

▲Up To Search▲

Price & Availability of AZ10LVEL16VST

	To Download AZ10LVEL16VST Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .